This entry turned out long, and that is our own fault: since 8 September we shipped more than ten updates and wrote about none of them. Here is everything that changed for those who calculate shipments — from the product card to the way work with the calculator now begins.
Goods no longer lose their card when you rename them
Previously the product name was both the name and the search key in the catalogue. One letter changed and the product detached from its card: models disappeared, and on save the card could take someone else's name.
Now the card starts with the factory: product type, factory brand or OEM, factory model. Below — the same for the buyer: your type, your brand, your model. Whatever you leave empty is taken from the factory, and the name is assembled from three parts by itself: «type + brand + model». You can edit it by hand, and if you later change the type or brand, the calculator shows next to it what the fields would produce and offers to restore it.
Typing in the «Name» field no longer detaches the card. You can change it only by picking from suggestions, and detach it with the cross next to the line «linked to card». Renamed «joint cutter» to «joint saw» — dimensions, HS code and prices stayed, while the documents carry the new name, including calculations saved earlier.
One more: «Save» no longer wipes from the card what the calculation does not have. If a product in the calculation has an empty HS code or dimension, the catalogue keeps them as they were.
You can see which rate each block was calculated at
A calculation has several rates: payment, customs, the agent's rate per tranche. Previously the report showed a total, and you had to reconstruct which rate produced it. Now rates and reference values sit in the block they belong to — on screen, in the «Calculation table», and in XLSX and PDF exports. The tranche agent's rate is a separate line, and «Customs rate» names the currency it is calculated for.
HS code and duty rate are now visible in the report too — one line per type, across product columns.
Duties by HS code: the full reference
We loaded the rate reference from the source layout: 12,913 rules — percentage, specific and combined rates in euros and roubles per kilogram, litre or piece. Whatever the calculator cannot parse unambiguously, it does not guess but lists on load, with reasons.
The excise got a base of assessment: per whole consignment, per piece, per kilogram, per litre. A rate per tonne with accounting in kilograms is now converted correctly, and excise per square metre takes the area of one piece.
The numbers that changed — said plainly
EPTS, SKBTS and EPSM are now charged per piece of goods: the amount in the card is the price of one document, and it is multiplied by quantity. Previously it applied to the whole consignment. As before, these documents are not included in the duty base or import VAT. If your calculations contain such documents, the cost after recalculation will rise — and that is the correct figure, not an error. The formula version went up to 1.9.
There was an unpleasant story too. Until 23 September a calculation with a custom percentage duty rate did not calculate at all: the page sent extra fields and the server rejected such a rule. Fixed, and an error in a duty rule now names the product.
The second story is worse because it was invisible. If you opened an old calculation right after another one, the page could keep the transport profile, route or agent mode from the previous one — and the calculation was silently computed under someone else's terms. In one of our calculations the cost came out 32 percent below the real one. Now all of this comes from the calculation itself, and is reset if absent. Fixed on 23 September, and we advise recalculating old calculations you opened and re-saved before that date.
And the third: the calculation history lost runs — those with a container layout, more than half. The calculation was computed but did not reach history. Now all of them do.
Settings read in order
Settings are arranged the way goods move: invoice currency sits in «General» right after suppliers, because it sets the currency prices are entered in, and selling terms are split into «Importer's sale price» and «Marketplace».
The price ladder — markup, retail price rule, «our prices are not lower» and competitor binding — is now set once per calculation. Per-product terms are switched on with one toggle per group; while off, the product card offers no terms of its own and confuses nothing.
How to start now
Open access without registration is closed. Registration is free, needs no card, and gives a free plan with no time limit: full cost calculation without restrictions, three saved calculations and three PDF/XLSX exports per week, your own supplier and counterparty references.
The 14-day Pro trial is now switched on in your account with one button: dealers, marketplaces, an agent in China, risk stress modes. Once per account and only from the free plan — so the trial does not eat an already paid Standard.
Small things
The «Collapse settings» button moved to the left menu, between «Scenario settings» and the sections. Results are now closed with one «← To goods» button, left of the heading, instead of two in different corners. The settings area is separated from goods by a dark band: white on white blurred together.
Exported documents can be styled in your brand and colours — write to us, we set it up ourselves.
The moral of this entry is simple: a calculator that computes imports must first of all not lie, and only then be convenient. Most of September went into the first — but we did not forget the second.